The Cisco switch must not have the default VLAN assigned to any host-facing switch ports.

Severity	Group ID	Group Title	Version	Rule ID	Date	STIG Version
medium	V-220691	SRG-NET-000512-L2S-000008	CISC-L2-000220	SV-220691r991947_rule	2024-08-22	3

Description
In a VLAN-based network, switches use the default VLAN (i.e., VLAN 1) for in-band management and to communicate with other networking devices using Spanning-Tree Protocol (STP), Dynamic Trunking Protocol (DTP), VLAN Trunking Protocol (VTP), and Port Aggregation Protocol (PAgP)—all untagged traffic. As a consequence, the default VLAN may unwisely span the entire network if not appropriately pruned. If its scope is large enough, the risk of compromise can increase significantly.

Description

In a VLAN-based network, switches use the default VLAN (i.e., VLAN 1) for in-band management and to communicate with other networking devices using Spanning-Tree Protocol (STP), Dynamic Trunking Protocol (DTP), VLAN Trunking Protocol (VTP), and Port Aggregation Protocol (PAgP)—all untagged traffic. As a consequence, the default VLAN may unwisely span the entire network if not appropriately pruned. If its scope is large enough, the risk of compromise can increase significantly.

ℹ️ Check
Review the switch configurations and verify that no access switch ports have been assigned membership to the default VLAN (i.e., VLAN 1). VLAN assignments can be verified via the show vlan command. In the example below, interfaces 1/1 and 1/2 are trunk links. SW1# show vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Eth1/1, Eth1/2 10 VLAN0010 active Eth1/1, Eth1/2, Eth1/3, Eth1/4 Eth1/5, Eth1/6, Eth1/7, Eth1/8 Eth1/9, Eth1/10, Eth1/11 Eth1/12, Eth1/13, Eth1/14 Eth1/15, Eth1/16, Eth1/17 Eth1/18, Eth1/19, Eth1/20 Eth1/21, Eth1/22, Eth1/23 Eth1/24, Eth1/25, Eth1/26 Eth1/27, Eth1/28, Eth1/29 Eth1/30 11 VLAN0011 active Eth1/1, Eth1/2, Eth1/31 Eth1/32, Eth1/33, Eth1/34 Eth1/35, Eth1/36, Eth1/37 Eth1/38, Eth1/39, Eth1/40 If there are access switch ports assigned to the default VLAN, this is a finding.

ℹ️ Check

Review the switch configurations and verify that no access switch ports have been assigned membership to the default VLAN (i.e., VLAN 1). VLAN assignments can be verified via the show vlan command. In the example below, interfaces 1/1 and 1/2 are trunk links. SW1# show vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Eth1/1, Eth1/2 10 VLAN0010 active Eth1/1, Eth1/2, Eth1/3, Eth1/4 Eth1/5, Eth1/6, Eth1/7, Eth1/8 Eth1/9, Eth1/10, Eth1/11 Eth1/12, Eth1/13, Eth1/14 Eth1/15, Eth1/16, Eth1/17 Eth1/18, Eth1/19, Eth1/20 Eth1/21, Eth1/22, Eth1/23 Eth1/24, Eth1/25, Eth1/26 Eth1/27, Eth1/28, Eth1/29 Eth1/30 11 VLAN0011 active Eth1/1, Eth1/2, Eth1/31 Eth1/32, Eth1/33, Eth1/34 Eth1/35, Eth1/36, Eth1/37 Eth1/38, Eth1/39, Eth1/40 If there are access switch ports assigned to the default VLAN, this is a finding.

✔️ Fix
Remove the assignment of the default VLAN from all access switch ports.